to top Arrow Up

MT1250 RMD

Aluminum cover RMD cover with hinge in the outer radius

mt0950-rmd_start.png

Properties

  • Aluminum cover system with hinge for light and medium loads. Assembly without screws.
  • Available customized in 1 mm sections.
  • Outside: swivable to both sides.
  • Inside: release by turning 90°.
test
Stay arrangement on every chain link

Stay arrangement on each chain link (VS: fully-stayed)

Inner width (B<sub>i</sub>) in 1 mm increments
Bi 150 – 800 mm in 1 mm width sections

Dimensions

Dimensions
Important information

The maximum cable diameter strongly depends on the bending radius and the desired cable type. Please contact us.

Important information

For rough environmental conditions, we recommend the use of OFFROAD glide shoes with 80 % higher wear volume.

Calculating the cable carrier length
Cable carrier length LK: LK ≈ LS/2 + LB
Cable carrier length Lk rounded to pitch t
t
[mm]
hi
[mm]
hG
[mm]
hG'
[mm]
hG' Offroad
[mm]
Bi
[mm] *
Bk
[mm]
BEF
[mm]
qk
[kg/m]
12568.59699.5103150 – 800Bi + 45Bi + 459.29 – 26.34
* in 1 mm width sections
KR
[mm]
260300340380500
Order example
Order code

MT1250

600

RMD

300

4250

VS

Our technical support can provide help for gliding arrangements: postmaster@metool.com

Inner distribution

Divider systems

As a standard, the divider system is mounted on every 2nd chain link.

As a standard, dividers or the complete divider system (dividers with height separations) are movable in the cross section (version A).

 

Divider system TS0

without hight separation
Vers.
aT min
[mm]
ax min
[mm]
ac min
[mm]
nT min
A6128

The dividers can be moved in the cross section.

Divider system TS0

Divider system TS1

with continuous height spearation
Vers.
aT min
[mm]
aT max
[mm]
ax min
[mm]
ac min
[mm]
nT min
A6251282

The dividers can be moved in the cross section.

Divider system TS1

Divider system TS2

with partial height separation
Vers.
aT min
[mm]
ax min
[mm]
ac min
[mm]
nT min
A721152

With grid distribution (1 mm grid). The dividers are attached by the height separation, the grid can be moved in the cross section.

Sliding dividers are optionally available (thickness of divider = 4 mm)

Divider system TS2
Order example
Order code

TS2

A

3

K1

K4

34

38

VR1

VR3

Please state the designation of the divider system (TS0, TS1 …), version and number of dividers per cross section [nT]. In addition, please also enter the chambers [K] from left to right, as well as the assembly distances [aT/ax] (as seen from the driver).

If using divider systems with height separation (TS1 – TS2), please also state the positions (e.g. VD23) viewed from the left driver belt. You are welcome to add a sketch to your order.

 

End connectors

MT1250 Universal connection element UMB - plastic
MT1250 Universal connection element UMB - plastic
Important information

Recommended tightening torque: 54 Nm for cheese-head screws ISO 4762 - M10 - 8.8

MT1250 Universal connection element UMB - plastic
Connection point

F – fixed point
M – driver

Connection type

U – universal end connector

MT1250 End connectors - plastic/steel
MT1250 End connectors - plastic/steel
MT1250 End connectors - plastic/steelMT1250 End connectors - plastic/steel
Connection point

F – fixed point
M – driver

Connection type

A – threaded joint outside (standard)
I – threaded joint inside
F – flange connection

Connection surface

I – connection surface inside
A – connection surface outside

Order example
Order code

Plastic/steel

F

A

A

UMB

M

U

 

End connector

Plastic/steel

UMB

Connection point

F

M

Connection type

A

U

Connection surface

A

Important information

We recommend the use of strain reliefs at the driver and fixed point.

Downloads

Matching with

Cables for cable carriers – TRAXLINE®

Reliable, robust with high availability. Your benefit from many years of experience combined with ongoing optimization, proven in tests and praxis. TRAXLINE® cables stand for competent system-supply with worldwide on-site service.

to TRAXLINE®

Ready-to-connect cable carrier systems – TOTALTRAX®

From pre-assembled cables to complex, ready-to-connect systems, from lot size 1 to series – worldwide thousands of KABELSCHLEPP systems are reliably in use. The benefits of TOTALTRAX® systems are obvious: just one person of contact, one order number, delivery just-in-time to your production facility, shortest downtimes thanks to plug&play installation.

to TOTALTRAX®

Accessories

Reliable unrolling and optimum gliding for long travel lengths

to Support trays
to Guide channels

For optimum placement with dynamic use of cables

to Strain relief devices

Services

Product Configurator
Product Configurator
Close

Product Configurator

  • Efficient, quick and complete configuration ­ the result is your individual product with an excellent price-performance ratio
  • Product configurator OnlineEngineer + suitable CAD model from CADenas without having to exit the portal
CADenas
CADenas
Close

CADenas

  • Decrease your engineering times
  • Accelerate your design processes
  • Configure with original data directly from the manufacturer
  • Providing 3D component models in a variety of CAD formats
Glossary
Glossary
Close

Glossary

Cable Carriers – Overview of general abbreviations and pictographs

Technical information
Technical information
Close

Technical information

Configuration guidelines:

  • Selecting a suitable cable carrier
  • Placement guidelines for cables and hoses
  • Installation variants
Literature
Literature
Close

Literature

The latest TSUBAKI KABELSCHLEPP information material:

Subject to change.
Contact
Please contact us:
Your contact: