to top Arrow Up

MT1250 RDD

Plastic cover RDD – cover with hinge in the outer radius

mt1250-rdd_start.png

Properties

  • Plastic cover system with hinge for light and medium loads. Assembly without screws.
  • Available customized in 16 mm sections.
  • Outside: swivable to both sides.
  • Inside:  release by turning 90°.
test
Stay arrangement on every chain link

Stay arrangement on each chain link (VS: fully-stayed)

Inner width (B<sub>i</sub>) in 16 mm increments
Bi 103 – 359 mm in 16 mm width sections

Dimensions

Dimensions
Important information

The maximum cable diameter strongly depends on the bending radius and the desired cable type. Please contact us.

Important information

For rough environmental conditions, we recommend the use of OFFROAD glide shoes with 80 % higher wear volume.

Calculating the cable carrier length
Cable carrier length LK: LK ≈ LS/2 + LB
Cable carrier length Lk rounded to pitch t
t
[mm]
hi
[mm]
hG
[mm]
hG'
[mm]
hG' Offroad
[mm]
Bk
[mm]
BEF
[mm]
qk
[kg/m]
12568.59699.5103Bi + 45Bi + 455.70 – 8.90
* in 16 mm width sections
Bi
[mm]
103119135151167183199215231247
263279295311327343359
KR
[mm]
220260300340380500
Order example
Order code

MT1250

295

RDD

300

4250

VS

Our technical support can provide help for gliding arrangements: postmaster@metool.com

Inner distribution

Divider systems

As a standard, the divider system is assembled at every 2nd chain link.

For applications with lateral acceleration and laying on the side, the dividers or the complete divider system (dividers with height separations) are fixed in the cross section. The arresting cams click into place in the locking grids in the crossbars (version B).

Divider system TS0

without height separation
Vers.
aT min
[mm]
ax min
[mm]
ac min
[mm]
ax grid
[mm]
nT min
B19.516816

The dividers are fixed in the cross section (version B).

Divider system TS0

Divider system TS1

with continuous height separation
Vers.
aT min
[mm]
aT max
[mm]
ax min
[mm]
ac min
[mm]
ax grid
[mm]
nT min
B19.519.5168162

The dividers are fixed in the cross section (version B).

Divider system TS1

Divider system TS2

with partial hight separation
Vers.
aT min
[mm]
ax min
[mm]
ac min
[mm]
ax grid
[mm]
nT min
B19.516*/328*/24162

* for VR0

With grid distribution (16 mm grid). The dividers are fixed by the height separation, the grid is fixed in the cross section (version B).

Divider system TS2

Divider system TS3

with height separation made of plastic partitions
Vers.
aT min
[mm]
ax min
[mm]
ac min
[mm]
nT min
B4/16*16/42**82

* for VR0 
** for aluminum partitions

The dividers are fixed with the partitions. The entire divider system can be moved in the cross section.

Divider system TS3
Divider system TS3

Aluminum partitions in 1 mm width sections with ax > 42 mm are also available.

ax (center distance of dividers) [mm]
ac (nominal width of inner chamber) [mm]
16
8
32
24
48
40
64
56
80
72
96
88
112
104
128
120
144
136
160
152
176
168
192
184
208
200

When using plastic partitions with ax > 112 mm, we recommend an additional center support with a twin divider (ST = 4 mm). Twin dividers are also suitable for retrofitting in the partition system. The height separations VR8 and VR9 are not possible when using twin dividers.

Order example
Order code

TS3

B

3

K1

K4

34

38

VR1

VR3

Please state the designation of the divider system (TS0, TS1,...), version and number of dividers per cross section [nT ]. In addition, please also enter the chambers [K] from left to right, as well as the assembly distances [aT/ax] (as seen from the driver).

If using divider systems with height separation (TS1 – TS3), please also state the positions [e.g. VD23] viewed from the left driver belt. You are welcome to add a sketch to your order.

End connectors

MT1250 Universal connection element UMB - plastic
MT1250 Universal connection element UMB - plastic
Important information

Recommended tightening torque: 54 Nm for cheese-head screws ISO 4762 - M10 - 8.8

MT1250 Universal connection element UMB - plastic
Connection point

F – fixed point
M – driver

Connection type

U – universal end connector

MT1250 End connectors - plastic/steel
MT1250 End connectors - plastic/steel
MT1250 End connectors - plastic/steelMT1250 End connectors - plastic/steel
Connection point

F – fixed point
M – driver

Connection type

A – threaded joint outside (standard)
I – threaded joint inside
F – flange connection

Connection surface

I – connection surface inside
A – connection surface outside

Order example
Order code

Plastic/steel

F

A

A

UMB

M

U

 

End connector

Plastic/steel

UMB

Connection point

F

M

Connection type

A

U

Connection surface

A

Important information

We recommend the use of strain reliefs at the driver and fixed point.

Downloads

Matching with

Cables for cable carriers – TRAXLINE®

Reliable, robust with high availability. Your benefit from many years of experience combined with ongoing optimization, proven in tests and praxis. TRAXLINE® cables stand for competent system-supply with worldwide on-site service.

to TRAXLINE®

Ready-to-connect cable carrier systems – TOTALTRAX®

From pre-assembled cables to complex, ready-to-connect systems, from lot size 1 to series – worldwide thousands of KABELSCHLEPP systems are reliably in use. The benefits of TOTALTRAX® systems are obvious: just one person of contact, one order number, delivery just-in-time to your production facility, shortest downtimes thanks to plug&play installation.

to TOTALTRAX®

Accessories

Reliable unrolling and optimum gliding for long travel lengths

to Support trays
to Guide channels

For optimum placement with dynamic use of cables

to Strain relief devices

Services

Product Configurator
Product Configurator
Close

Product Configurator

  • Efficient, quick and complete configuration ­ the result is your individual product with an excellent price-performance ratio
  • Product configurator OnlineEngineer + suitable CAD model from CADenas without having to exit the portal
CADenas
CADenas
Close

CADenas

  • Decrease your engineering times
  • Accelerate your design processes
  • Configure with original data directly from the manufacturer
  • Providing 3D component models in a variety of CAD formats
Glossary
Glossary
Close

Glossary

Cable Carriers – Overview of general abbreviations and pictographs

Technical information
Technical information
Close

Technical information

Configuration guidelines:

  • Selecting a suitable cable carrier
  • Placement guidelines for cables and hoses
  • Installation variants
Literature
Literature
Close

Literature

The latest TSUBAKI KABELSCHLEPP information material:

Subject to change.
Contact
Please contact us:
Your contact: